How to deal with the scratch on the surface of hydraulic cylinder barrel

As we all know,In the process of using the hydraulic cylinder, the hydraulic cylinder barrel will be damaged,it is common that there will be scratch on the surface of the honed tube, some customers will ignore these scratches, this to us is not responsible for the cylinder, when a small scratches in the cylinder,we usually take some tips to deal with them.

1.First, to clean up the oil on the surface of our hydraulic cylinder barrel, then we will use the grinder machine to the surface treatment of the scratched part of our cylinder, at this time we have to grind the surface of the cylinder wall out of swallowtail groove.Although we have cleaned our cylinder at the beginning, at this time we need to clean the cylinder barrel further. At this time, we use anhydrous ethanol to clean the surface of the scratch repair of honed cylinder barrel.

2.We usually use special repairing adhesive to solve the scratches on the surface of hydraulic cylinder barrel, before using it, we need to check the expiry date of the repairing adhesive to see whether the repairing adhesive or validity range, in addition, although some repairing adhesive within the period of validity, but due to improper storage has failure, it also can not work, After our hydraulic cylinder repair agent is pressed hard repeatedly, remember to make it higher than the surface of the original wall cylinder, and then make the repaired part warm and solidify.


Comments

Post a Comment

Popular posts from this blog

40CR ALLOY STEEL SPECIFICATION

  40Cr steel  is a kind of Chinese GB standard alloy steel for engineering and machinery purpose, and one of the most widely used steel grades. For 40Cr material hardness, specifications and equivalent, please see the table below. After quenching and tempering treatment, 40Cr steel has good comprehensive mechanical properties, low temperature impact toughness, low notch sensitivity, good hardenability, and high fatigue strength in cold oil. When water cooling, the complicated shape of the parts is prone to cracks, the cold bending plasticity is medium, and the cutting workability after normalizing is good, but the weldability is poor, should be preheated before welding, and is generally used in the state of quenching and tempering. DATASHEET & SPECIFICATION The tables below list 40Cr alloy steel datasheet and specification including chemical composition, properties and heat treatment, etc. 40CR STEEL CHEMICAL COMPOSITION   Chemical Composition (%) Grade C % Si Mn Cr 40Cr 0.37 – 0.4
Read more

Skiving &Roller Burnishing Tube And Honing Tube

Image
Skiving and roller burnishing tube  process provide high quality hydraulic cylinders with final sizing and creates the desired finish pattern on the interior of tubing or cylinder bores. They are used in the manufacturing of  hydraulic cylinders . Compared to honing process, they are 80-90% saving of machine time which reduces tool costs per meter of tube length and produces super finish surface, with a bore tolerance of IT8, thereby reduces the sealing wear making it ideal for pistons. The skiving tool is a multifunctional tool used in the manufacturing of hydraulic cylinders. Skiving is operated like this: Two thin chips are cut at a high feed rate (1-4 mm/rev) while the tool passes through the work piece. This cutting operation determines the finished diameter and tolerance of the hydraulic tube. Surface finish Ra= 4-10 μm (skiving) Skiving has obvious advantages compared with honing: • 80-90% saving of machine time which reduces tool costs per meter of tube length. • Produ
Read more

What is Hydraulic Ram Cylinder?

Image
  Hydraulic ram cylinders   are typically used to give vertical motion, including lifting loads in a vertical direction. Such a cylinder is also used to provide the motion in a horizontal direction but needs attention and suitable guides to guide the motion. Single-acting hydraulic cylinders that have no pistons but have large  cylinder rod s are called rams. These rams operate exactly like the conventional single acting hydraulic  cylinders. However, they use large diameter rods in place of pistons and piston seals in their designs. Thus, in place of pistons, rams have high-pressure cap-end ports. They also do not have any low-pressure rod-end ports. Rams are generally cheaper than their conventional single-acting cylinders counterparts.
Read more