BRIF INDUCTION OF 4140 QUENCHED + TEMPERED HARDNESS HRC

 SAE 4140 steel can be used in a ready-made semi-hardened (quenched + tempered) state. Its hardness is in the range of 28-32 HRc. It is a material known as tempering steel in the industry, which can be used in hydraulic cylinder shafts, gears, and machine parts working under high tensile strength thanks to its high tensile strength.

4140 is a medium-carbon (nominal 0.40%C) chromium-molybdenum alloy steel that is most often oil quenched to attain an as-quenched hardness ranging from about 54-59 HRC (as quenched), depending on the precise carbon content (which affects the hardenability of the material).

Applications of Grade 4140 Quench +Tempered


Medium-high stressed 4140  shafts and components where the use of carbon steel 1045 would not be appropriate. Reasons for using 4140 are the higher yield and fatigue strength, better through hardening of the material and superior impact properties compared to plain carbon steels like 1045. These advantages are only achieved when 4140 is used in the heat-treated condition. Typical components include transmission shafts, cylinder piston rods , spindles and small gears, threaded fasteners such as bolts, nuts and studs.

4140 round bar


Comments

Post a Comment

Popular posts from this blog

40CR ALLOY STEEL SPECIFICATION

  40Cr steel  is a kind of Chinese GB standard alloy steel for engineering and machinery purpose, and one of the most widely used steel grades. For 40Cr material hardness, specifications and equivalent, please see the table below. After quenching and tempering treatment, 40Cr steel has good comprehensive mechanical properties, low temperature impact toughness, low notch sensitivity, good hardenability, and high fatigue strength in cold oil. When water cooling, the complicated shape of the parts is prone to cracks, the cold bending plasticity is medium, and the cutting workability after normalizing is good, but the weldability is poor, should be preheated before welding, and is generally used in the state of quenching and tempering. DATASHEET & SPECIFICATION The tables below list 40Cr alloy steel datasheet and specification including chemical composition, properties and heat treatment, etc. 40CR STEEL CHEMICAL COMPOSITION   Chemical Composition (%) Grade C % Si Mn Cr 40Cr 0.37 – 0.4
Read more

Skiving &Roller Burnishing Tube And Honing Tube

Image
Skiving and roller burnishing tube  process provide high quality hydraulic cylinders with final sizing and creates the desired finish pattern on the interior of tubing or cylinder bores. They are used in the manufacturing of  hydraulic cylinders . Compared to honing process, they are 80-90% saving of machine time which reduces tool costs per meter of tube length and produces super finish surface, with a bore tolerance of IT8, thereby reduces the sealing wear making it ideal for pistons. The skiving tool is a multifunctional tool used in the manufacturing of hydraulic cylinders. Skiving is operated like this: Two thin chips are cut at a high feed rate (1-4 mm/rev) while the tool passes through the work piece. This cutting operation determines the finished diameter and tolerance of the hydraulic tube. Surface finish Ra= 4-10 μm (skiving) Skiving has obvious advantages compared with honing: • 80-90% saving of machine time which reduces tool costs per meter of tube length. • Produ
Read more

What is Hydraulic Ram Cylinder?

Image
  Hydraulic ram cylinders   are typically used to give vertical motion, including lifting loads in a vertical direction. Such a cylinder is also used to provide the motion in a horizontal direction but needs attention and suitable guides to guide the motion. Single-acting hydraulic cylinders that have no pistons but have large  cylinder rod s are called rams. These rams operate exactly like the conventional single acting hydraulic  cylinders. However, they use large diameter rods in place of pistons and piston seals in their designs. Thus, in place of pistons, rams have high-pressure cap-end ports. They also do not have any low-pressure rod-end ports. Rams are generally cheaper than their conventional single-acting cylinders counterparts.
Read more